Fulltext results:
- Heated basement @basics:building_physics_-_basics:thermal_bridges:tbcalculation:examples
- ement ceiling and the connection of the basement wall to the basement floor slab. In the Ground workshe... ues for the basement floor slab and the basement wall are determined using the approximation function i... ne the Ψ-value, the conductances of the exterior wall, the basement wall and the basement floor slab must also be calculated. The conductance of the exterio
- Interior walls on floor slabs @basics:building_physics_-_basics:thermal_bridges:tbcalculation:examples
- ====== Interior walls on floor slabs ====== Interior walls on floor slabs are often calculated two-dimensionally without the influence of the ground. The result ... matter of fact the thermal bridge of an interior wall on a floor slab depends on the distance from the
- Definition and effects of thermal bridges
- ing envelope where the heat flow is different (usually increased) in comparison with adjacent areas (if... ts of thermal bridges are: * **Altered**, usually decreased, interior **surface temperatures**; in... mponents and mould growth. * **Altered**, usually increased, **heat losses**.\\ \\ Both effects of... nsignificant. If the thermal bridge losses are smaller than a limit value (set at 0.01 W/(mK)), the de
- Exterior wall on floor slab @basics:building_physics_-_basics:thermal_bridges:tbcalculation:examples
- ====== Exterior wall on floor slab ====== A typical connection detail is shown below: {{ :picopen:aus... is disregarded because the insulating effect is small compared to the surrounding earth. The perimeter ... . The following U-value results for the exterior wall: {{ :picopen:aussenwand_auf_bodenplatte_abb_6.pn... \\ ===== Calculation model ===== First, an overall model is prepared for calculating the conductanc
- Special features and characteristics of components in contact with the ground @basics:building_physics_-_basics:thermal_bridges:tbcalculation:ground_contact
- omponents in contact with the ground ====== Basically the procedure for calculating thermal bridges in... e ground on the building envelope is known, especially in terms of setting the linear thermal transmitt... urroundings are very complex. This applies especially for the system "ground". Apart from the ground i... oor air temperature. Thus for example, snow that falls during temperatures around freezing point initia
- Unheated basement @basics:building_physics_-_basics:thermal_bridges:tbcalculation:examples
- lues of the basement floor slab and the basement wall respectively and are based in turn on the approxi... basement is also taken into account. In order to allow energy-relevant evaluation of the connection si... b_4.png?200|}} For the unheated basement, the overall value $L_{2d}$ must also be calculated as it is f... he boundary surface of the ceiling area, which usually is not true, of course. The difference to the re
- Recommended procedure for calculating thermal bridges of components in contact with the ground @basics:building_physics_-_basics:thermal_bridges:tbcalculation:ground_contact
- mal bridges towards the ground). The ground especially is taken into account in the calculation in diff... * partial taking into account the ground with small layers of earth or with small blocks of earth in the calculation models * no depiction of the groun... temperature (see DIN 4108 Supplementray Sheet 2) All methods constitute an estimation ultimately; neve
- Basic principle for calculating thermal bridges @basics:building_physics_-_basics:thermal_bridges:tbcalculation
- -value represents the difference between the thermally interrupted component and the uninterrupted comp... essential that the linear reference is adhered to all throughout. If interior references are used in th... ng the surface temperatures is similar and can usually take place using the same model as for calculati... de space. The reason for this is that wardrobes, wall coverings, curtains and the like reduce convectio
- Thermal Bridges
- Thermal bridges catalogue for brick and concrete walls]] * [[.:window_installation_thermal_bridges_catalogue|Window installation thermal bridges catalogue]]
- Thermal bridge calculation
- ined with the aid of heat flow simulations, which allow conclusions to be drawn regarding thermal comfo... ns| Roof connections, ceiling/floor connections, wall corners... | DIN EN ISO 10211
- Software for calculating thermal bridges @basics:building_physics_-_basics:thermal_bridges:tbcalculation
- solve this partial differential equation analytically. However, for a time-independent case which is o... s, the Fourier equation must be calculated numerically using computer-assisted methods. Typical heat fl... software programs available on the market are usually characterised by the following programme structu
- Thermal Bridges Catalogue
- nge of insulation thickness from 0-400mm, thereby allowing the identification of Ψ-values for the use w