Fulltext results:
- Economic analysis for the retrofit of a detached single family house to the EnerPHit standard
- insulation directly on the slab, so buried walls have been insulated externally on the perimeter of the... slab with 16cm of extruded polystyrene. Windows have been replaced by Smartwin wood-aluminium frames (... ped with movable shutters. Existing shutter-boxes have been insulated with mineral wool and taped to be ... aced below the ceiling brickwork, interior bricks have then been cut on the external walls to tape the m
- Overall retrofit plan for step-by-step retrofits to EnerPHit Standard
- gramme, deep renovations carried out step by step have been the focus of a consortium of 14 partners all... the costs for retrofits of residential buildings have been invested into single measures or packages of... se study projects with at least one retrofit step have been completed by April 2016, 9 more projects are currently ongoing and will have completed retrofit measures after the project com
- Component Award 2016: Affordable ventilation solutions for retrofits
- ly air into neighbouring rooms. These ventilators have very low power consumption of about 1 W. The retu... check of condensate drain). Improved ventilators have considerably reduced the specific power consumpti... lly for small ventilators. The duct networks must have low pressure losses for the ventilators to be eff... ssive power consumption levels. Air volumes also have to be constantly balanced for efficient operation
- Refurbishment with Passive House components - introduction
- ssess whether the finished modernisation projects have proved successful in operation. After completion ... /|\\ \\ Thus, the principle to be followed, as we have always maintained, is: if it has to be done, it s... he measures. Many countries and regions in Europe have similar programmes, as in most Austrian States fo... also benefit from all the other advantages, which have already been explained.\\ \\ The following demand
- Step-by-step Retrofits towards EnerPHit Standard in social housing in Spain
- cant for some time (Figure 2). The current owners have done a refurbishment to prepare it for their pres... ng 4, 6 and 8 cm of mineral wool inner insulation have been calculated with PHPP software (Table 1). Bec... e on the flat from the inside and no common areas have been affected, neighbourhood association approval... ess. In particular, the airtightness improvements have to be made between the original wall and the ETIC
- Windows in a step-by-step retrofit
- . In the end, once the wall is insulated, it will have thermal bridges from installation, and solar gain... façade is renovated, the window frame can easily have insulation added to it. All other solutions turne... ore or less cold outdoor air, insulation does not have any advantages. It is therefore recommended tha... front-wall mounting system. It is a good idea to have the slats roll to the outside; the guide rails ar
- Influence of retrofitting on daylighting @planning:refurbishment_with_passive_house_components:mechanical_systems
- duction ===== Some building physics projects can have a direct impact on daylighting. Optimized lightin... daylighting is desirable. Most existing buildings have defined daylight openings that can be altered only minimally. Retrofits can also have a negative impact on daylight supply, primarily i... back the window reveal or designing the reveal to have a high reflection factor. Choosing different glas
- Airtightness and airtightness measurement @planning:refurbishment_with_passive_house_components:thermal_envelope
- h heat losses. That is why airtightness standards have been set for many years and why we still have them in current regulations. It is still widely beleived... / || Pressure test results of old buildings that have not been modernised are often in the range betwee... efurbished. It is not known what effect this will have on the airtightness of the building, therefore ai
- Step-by-step deep retrofit and building integrated façade/roof on a 'million program' house
- 0 mm cellulose fibre (cold attic). These upgrades have already reduced the heating demand to roughly hal... point fasteners to hold the modules in place may have been a simpler solution, if not for the reason th... the furring is made of metal. Wood furring would have been preferred considering the environmental impa... ith the authors. \\ While certain marked articles have been created with the support of the EU, they do
- Prospects for the modernisation of existing buildings using highly efficient components
- apartments and commercial spaces involved usually have a functioning heat distribution system (usually b... f the energy-efficient modernisation of buildings have been started recently. Avoiding the mistakes of t
- Improving thermal bridges and airtightness in existing buildings @planning:refurbishment_with_passive_house_components:thermal_envelope
- e details with improved insulation on the outside have higher interior surface temperatures. The risk of... mproved insulation. Some details in old buildings have such enormous thermal bridges that only insulatio
- Building Integrated Photovoltaics (BIPV) in Step by Step Retrofitting Projects
- ith the authors. \\ While certain marked articles have been created with the support of the EU, they do
- Floor Replacement: Svartbäcksvägen @planning:refurbishment_with_passive_house_components:thermal_envelope
- ith the authors. \\ While certain marked articles have been created with the support of the EU, they do
- Crosstalk silencers @planning:refurbishment_with_passive_house_components:ventilation
- eter of about 10 cm). Bends and bifurcations only have a slightly damping effect: without any preventive