Fulltext results:
- Overall retrofit plan for step-by-step retrofits to EnerPHit Standard
- rofit plan for step-by-step retrofits to EnerPHit Standard ====== Jan Steiger and Eva Vahalova, Passive Hou... al social high-rise buildings, where the EnerPHit Standard was implemented completely except for a more effi... of more than 40.000 m² of floor area to EnerPHit Standard. \\ \\ ===== 3 Types of step-by-step retrofit pro... easures are implemented to finally reach EnerPHit Standard (Figure 2). **Sequential retrofitting of buildin
- Economic analysis for the retrofit of a detached single family house to the EnerPHit standard
- of a detached single family house to the EnerPHit standard ====== **Author: Simon Camal, La Maison Passive**... ls installed on the roof. **3. Comparison with a standard low-energy variant** \\ The economic performance ... assive House projects is continuously compared to standard low-energy alternatives. Additional investment in... ventilation with heat recovery. * Ventilation: standard deviation is chosen equal to the investment reduc
- Step-by-step deep retrofit and building integrated façade/roof on a 'million program' house
- steps of a step-by-step retrofit to Passive House Standard. The scope of the project includes that the exist... ting ‘million program’ buildings to Passive House Standard with external insulation and a new façade and roo... 15 kWh/(m2a) (i.e. to international Passive House Standard) and electricity consumption to approximately 30 ... step-by-step retrofit approaches to the EnerPHit Standard [4]. In this demonstration project, since it is d
- Improving thermal bridges and airtightness in existing buildings @planning:refurbishment_with_passive_house_components:thermal_envelope
- |{{:picopen:fig.2_pb24.png?350|}}| |//**Figure 2: Standard building components – status quo**//|\\ The initial assumption is based on the two standard components shown in Fig. 2. The wall with its “on... for all details. \\ In order to achieve a good standard of airtightness, the same rules apply as for a ne... r, it will not be possible to achieve an adequate standard of airtightness. ===== Literature ===== **[AkkP
- Prospects for the modernisation of existing buildings using highly efficient components
- like compact heat pump units for example, a high standard of thermal protection, increased airtightness and... usually not possible to achieve the Passive House Standard at reasonable cost by means of the procedures and... savings. \\ The attractiveness of a high quality standard of modernisation increases with the use of highly
- Step-by-step Retrofits towards EnerPHit Standard in social housing in Spain
- \ ====== Step-by-step Retrofits towards EnerPHit Standard in social housing in Spain ====== Nuria Díaz Ant... on for the whole building to achieve the EnerPHit standard requirements. Refurbishment projects face an add... ogether with other measures to reach the EnerPHit standard. These modifications were initiated thanks to the
- Airtightness and airtightness measurement @planning:refurbishment_with_passive_house_components:thermal_envelope
- ith the [[.:airtightness#literature|[EN 13829] ]] standard, the measurement is also valid if a pressure diff... atures_in_modernisations#literature|[EN 13829] ]] standard facilitates the test in old buildings for which n... - construction techniques for airtightness in **standard surfaces**, - airtight **connections** of buil
- Refurbishment with Passive House components - introduction
- justed for an\\ interior temperature of 20 °C and standard\\ climate) after modernisation of the projects in... radically again when the Passive House becomes a standard on the market. Above all, crafts businesses, arch
- Windows in a step-by-step retrofit
- House frames are required for this situation; if standard frames are used, the temperatures at the interior... anes for a total of 44 mm. For such glazing for a standard IV 68 window, the pane-holding strip should be re
- Building Integrated Photovoltaics (BIPV) in Step by Step Retrofitting Projects
- 050, info@onyxsolar.com // \\ \\ The Passivhaus standard was initially developed in Germany for mid and no
- Floor Replacement: Svartbäcksvägen @planning:refurbishment_with_passive_house_components:thermal_envelope
- s, being step-by-step retrofitted to the EnerPHit standard. The first step was to make the basement habita